Architecture and determinism
Loop rates, multi-rate model scheduling, core allocation, latency and jitter budgets, data logging. We design the frame so it holds under load.
Real-time simulation
We design, integrate and troubleshoot real-time simulation systems for automotive and aerospace programmes: driving simulators, hardware-in-the-loop rigs and test benches where models, I/O and hardware have to stay in step every frame. We were core developers of SIMulation Workbench, so we know these systems from the scheduler up.
Services
Loop rates, multi-rate model scheduling, core allocation, latency and jitter budgets, data logging. We design the frame so it holds under load.
CAN, SOME/IP, FlexRay, ARINC 429, MIL-STD-1553, analog, digital, PWM and the rest of the table below: signal mapping, conditioning, restbus simulation and validation against the real hardware.
Simulink, Simpack, MSC Adams, FMI/FMU and hand-written C, C++ and Python models running together at real-time rates, with parameters you can change while the test runs.
Connecting SIMulation Workbench with Simulink Real-Time, dSPACE and NI systems, and with image generators such as rFpro and Diamond Visionics GenesisRTX.
Wiring and signal checks, timing problems, model overruns, flaky buses and the long tail of issues that only appear once everything is connected.
Scripted test sessions, recording and playback, integration with your CI, and training so your team can run and extend the rig without us.
Interfaces
Drawn from the interfaces SIMulation Workbench supports today. If yours is missing, ask.
| Interface | Where it shows up |
|---|---|
| CAN, CAN FD | Powertrain, body and chassis ECU networks; restbus simulation of the nodes that are not on the bench |
| LIN | Single-wire sub-buses for doors, wipers, headlights and other small ECUs; the commander's schedule or the responders that are not on the bench |
| Automotive Ethernet, SOME/IP | Service-oriented ECU communication, with the network defined from AUTOSAR ARXML files |
| FlexRay | Time-triggered chassis and safety networks |
| ARINC 429 | Avionics data buses between line-replaceable units |
| AFDX (ARINC 664 Part 7) | Deterministic switched Ethernet between avionics systems, with virtual links and redundant networks |
| MIL-STD-1553 | Dual-redundant command and response buses in military avionics and missile systems |
| Analog in and out | Sensor and actuator signals, from potentiometers and pressure transducers to command voltages |
| Digital I/O | Discretes, switches, status lines and relay contacts |
| PWM, pulse and frequency | Actuator drive signals, speed sensors and encoders |
| Resolver, synchro, LVDT, RVDT | Position feedback in flight controls, actuation and high-lift systems |
| Resistance simulation | Resistive sensors such as thermistors and RTDs presented to the unit under test |
| RS-232, RS-422, RS-485 | Instrumentation, legacy controllers and navigation sensor feeds |
| Reflective memory | Low-latency links between simulation hosts, image generators and motion systems |
| Ethernet UDP, TCP | Image generators, motion platforms, test automation and data logging |
Tools
Applications
Driver-in-the-loop simulators where the vehicle model, motion cueing, image generation and the cockpit's buses and signals all run in lock-step. We integrate vehicle dynamics from Simulink, Simpack or Adams with image generators such as rFpro, and keep the whole loop deterministic.
Benches that test ECUs and subsystems against simulated plants: sensor and actuator emulation, restbus simulation, fault injection, automated regression runs and the data logging to prove what happened.
Hardware-in-the-loop validation of guidance, navigation and control: flight models, sensor and actuator interfaces, bus traffic and repeatable engagement scenarios, all under hard real-time timing.
Including high-lift system testing for Airbus: flap and slat actuation and control exercised against a real-time simulation of the aircraft's interfaces, loads and failure cases.
Start a conversation